What amp should I charge my NiMH RC battery?
The high-performance NiMH battery chargers with a minimum charge rate of 4 to 5 amps in one cycle are required and needed to charge the high capacity NiMH batteries completely that varies around 3000 to 5000 mAH.
Can I charge a 9.6 V battery with a 12V charger?
Therefore, for your 9.6 volt, 500 mAh battery, the charger should have a voltage output of no less than 12 volts (that’s open circuit voltage actually measured and not what’s written on the charger) and should have a current rating of no more than 0.5 amps (500 mAh) for a 1C charge rate.
Can I charge NiMH batteries with any charger?
Never charge an NiMH cell with incorrect charger: It is never acceptable to charge a battery of any form with a charger that may be unsuitable. NiMH cells cannot be charged with a NiCd charger as end of charge detection will not work.
How do you charge a NiMH RC car?
Normal Charging The best way to charge a nickel metal hydride battery is to charge at C/10 or below (10% of the rated capacity per hour). So a 100 mAH battery would be charged at 10 mA for 15 hours. This method does not require an end-of-charge sensor and ensures a full charge.
Can I use a 9.6 V charger for a 7.2 V battery?
9.6V/7.2V RC Ni-Cd/NiMH Charger Your RadioShack 9.6V/7.2V RC Ni-Cd/Ni-MH Charger can fully charge 7.2V/9.6V nickel-cadmium (Ni-Cd) and nickel-metal hydride (Ni-MH) cord-connected battery packs used in many remote- controlled cars, in about 5 (for Ni-Cd) or 7.5 (for Ni-MH) hours.
What rate should I charge NiMH?
Overnight Charging The cheapest way to charge a nickel metal hydride battery is to charge at C/10 or below (10% of the rated capacity per hour). So a 100 mAH battery would be charged at 10 mA for 15 hours. This method does not require an end-of-charge sensor and ensures a full charge.
Can you use a 12 volt charger on a 9 volt battery?
Similarly, you can charge a 9V battery with a 12V charger, and we show it in more detail below with Lithium-ion and NiMH batteries . The 9V li-ion battery is made of two 3.6V cells lending it a nominal voltage of 8.4. To safely recharge it you need a voltage source of 8.4V.
Can I use a 12 volt battery on a 9 volt device?
You can’t use a 12V adapter to power a 9V guitar pedal. A pedal that only handles 9V can be destroyed by using a 12V adapter. It’s possible for a power supply to ruin your pedal even if you get the voltage right.
Do you need a special charger for NiMH batteries?
Do stay-charged or low discharge batteries need a special charger? No – any type of charger suitable for NiMH rechargeable batteries will charge either stay-charged or standard rechargeable batteries.
How do you know when NiMH battery is fully charged?
Usually, a fully charged battery would display a voltmeter reading of around 1.5 volts. That means your battery is in good shape if your voltmeter shows a voltage anywhere between 1.3-1.5 volts. 4)A strong indication that your battery has excessive voltage is any voltage above 1.5volts.
Can you charge a 8.4 V battery with a 9.6 V charger?
No. The output voltage on the charger needs to at least meet the voltage on the battery.
What size battery charger do I need for a NiMH battery pack?
Stay charged up- The 12V 400mA NiMH battery charger can charge NiMH/NiCd battery packs that are 9.6V (8S). NOTE: This charger is only for recharging NiMH/NiCd batteries, DO NOT recharge LiPo batteries or Spike the Dinosaur.
What do you need to know about the RC Battery charger?
Advanced protections – This 9.6V RC battery charger has built-in safety protections against reverse polarity, short circuit, and over-current protection. 12 months warranty – The universal 100-240V AC input enables this charger to be used anywhere.
What kind of battery does Tamiya use for RC cars?
Tenergy 12V 400mA RC hobbies battery charger for 9.6V (8S) NiMH/NiCd battery packs with standard male Tamiya connector. Ideal for RC cars with standard female Tamiya connector.