How do I fix code F01 on my Whirlpool Duet dryer?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.
How do you fix F01 on dryer?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes.
Is there a reset button on a Whirlpool Duet dryer?
You can reset a Whirlpool dryer by pressing and holding the start button for a few seconds. This should start the reset automatically.
What does f1 means on a dryer?
This code indicates that the thermistor has failed. The dryer won’t dry without a functioning thermistor because this is the mechanism that measures the internal temperature of the dryer so the machine can safely and efficiently dry the clothes.
Where is the thermal fuse on a Whirlpool Duet dryer?
Remove the back access panel on the dryer, and look for the exhaust duct near the bottom of the unit. The thermal fuse is either circular or oblong, often white plastic with black material in the center and two wire leads. The thermal fuse is mounted on the exhaust duct.
How do you troubleshoot a Whirlpool Duet dryer?
Whirlpool Duet Dryer Will Not Start
- Check the Circuits. Always check that the dryer is receiving the proper amount of 240v current.
- Check the Door Latch. The dryer will not start if the door latch is malfunctioning.
- Check the Thermal Fuse. Inspect the thermal fuse.
- Check the Start Button.
What would cause a Whirlpool dryer not to start?
Make sure the dryer is correctly plugged into the proper electrical outlet. Check for tripped breakers or blown fuses. If needed, reset any tripped breakers and replace blown fuses. Avoid using an extension cord.
What is E1 on Whirlpool Duet dryer?
The Whirlpool Duet Dryer Error E1 means the control has detected that the thermistor is open. This error can be a wiring issue from the control to the thermistor or a bad thermistor. In some cases it can be a bad control reporting false errors but this is not common.
What does f1 and E1 mean on a Whirlpool dryer?
A “F1E1” code in the display indicates there may be an issue with the control unit or the associated wiring. Touch POWER, select a cycle, then hold START/PAUSE button to start the dryer. If this is unsuccessful, unplug the dryer.
How do you fix a whirlpool duet dryer error code F01?
The Whirlpool Duet Dryer F01 error may be able to be fixed with a simple reset of the main control. Unplug the dryer for 1 minute and plug it back in this will reset the control if the error persists after that you will need to check the dryer thermal fuse. The fuse is located on top of the blower wheel housing.
Can a thermal fuse cause a F01 error on a dryer?
In most cases its not the fuse causing the F01 error code but it’s worth checking because in some rare cases it can be and it’s a $20.00 part VS a $200.00 part. To check the thermal fuse remove the bottom access panel off the front of the dryer and you will see the fuse mounted at the top of the blower wheel housing.
Why won’t my Whirlpool dryer start?
A whirlpool dryer may not start due to several reasons, not necessarily power. Perhaps the door switch is faulty, the thermal fuse has been blown, or the starter switch is experiencing some challenges. Sometimes it may only be the settings, or even worse, a defective drive motor.
How do I fix the error code F01 on my Kenmore washer?
The F01 error is an internal failure of the main control board. The only thing you can do is try and reset the electronics by killing power to it at the breaker/fuse panel on your home for one full minute then restore power. If after that the problem persists the control board will need to be replaced unfortunatley.